A Step-by-Step Guide to Installing a Tub
Request ServiceAre you hunting for suggestions on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately hard job. If the old tub is conveniently easily accessible, the project can relocate quickly; if you need to open a wall to eliminate the old tub as well as position the brand-new tub, the job is a lot harder. In either case, the task is within a house handyman's abilities, although you will need an assistant to move out the old tub and embeded in the new one. Make sure you have actually qualified on your own for the task and fit trying it. Rather than employing a professional to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Possibilities are you may require a professional plumber to make tube links.
This short article will assist you install a brand-new tub in your bathroom if you have actually already gotten a new bathtub and also don't require to alter the arrangement of your previous water system pipes.
Your devices and product checklist must comprise the following:
Preparing for the Setup
To start with, the supporting framework provided with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps system to prevent stress on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The process of removing the existing taps can be fairly bothersome as a result of the limited accessibility that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. Once the supply pipes have been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Before proceeding to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 little points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub till the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as check all joints and also brand-new pipework for leaks and also tighten them if needed. Fill the bath tub and also examine the overflow outlet and also the typical outlet for leakages.
Lastly, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bathtub must wait until the tub has actually been used at the very least once as this will certainly resolve it into its last position.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washing machines are in location in between the faucet and the sink. Protect the faucet in position with the producer supplied backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bath as well as the tiling, bring about complications with moisture and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can crack fairly early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily available on the market. It is suggested to fit the floor tiles making use of waterproof or water resistant sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our excerpt on Tools You Need to Install a New Bathtub . Thanks for spending some time to read through our blog post. Loved our write up? Please share it. Let someone else find it. We love reading our article about Installing A Bathtub.
Book Instantly